Heat flux Study guides, Class notes & Summaries

NATE AC Service Certification Questions And Answers 2023 Verified Tests A system is supplied from the factory with charge of 5 pounds 10 ounces for a 15 foot line set. The line set is 25 feet long. The manufacturer's instruction sheet specifies 0.6 ounces of refrigeration to be added for each added foot of refrigerant line set length. What is the total refrigerant charge for the system? A. 6 ounces B. 5 pounds C. 5 pounds 10 ounces D. 6 pounds D. 6 pounds 15ft - 25ft = 10ft x .6 = 6 o...

A system is supplied from the factory with charge of 5 pounds 10 ounces for a 15 foot line set. The line set is 25 feet long. The manufacturer's instruction sheet specifies 0.6 ounces of refrigeration to be added for each added foot of refrigerant line set length. What is the total refrigerant charge for the system? A. 6 ounces B. 5 pounds C. 5 pounds 10 ounces D. 6 pounds - D. 6 pounds 15ft - 25ft = 10ft x .6 = 6 ounces 5 pounds + 10 ounces + 6 ounces 5 pounds + 16 ounces = 6 pou...

On an R-22 system, line diameters and lengths are typically specified for a vapor pressure drop that does not exceed what? - ANSWER6-7PSI or 6F What is the primary purpose of using flux when soldering copper or brass parts? - ANSWERPrevent Oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must? - ANSWERDrain off and away from the outdoor coil. Why must the runoff be drained off and away from the outdoor coil? - ANSWERExcessive ice can build up on t...

Edexcel A Level Geography - The carbon cycle and energy security Exam Questions With Solutions (carbon) Flux - ANS Transfer of carbon from one 'pool' to another (carbon) store - ANS An accumulation of carbon Biosphere - ANS The regions of the surface and atmosphere of the earth occupied by living organisms Photosynthesis - ANS The process by which carbon atoms in the atmosphere move into trees and plants, plants use sunlight to synthesize nutrients from CO2 and water ...

IAAI CFI Study Questions 2021with All Correct Answers Combustible Liquid - ANSWER A liquid with a flash point ABOVE 100F 12.5 - ANSWER If the current flowing out from an electrical panel is 12.5 amps, and it then flows through an electrical load of 1500 watts, what is the amperage of the remaining current flow of the return circuit? 1000 - ANSWER If a hair dryer draws 8.3amps (in a home with 120-volt service), what is the wattage? *Power (P) = current (I) x voltage (V...

Test Bank for Fundamentals of Physics, Extended, 12e 12th Edition by David Halliday, Robert Resnick, Jearl Walker. Full Chapters test bank are included - Chapter 1 to 44 1 Measurement 1 1.1 Measuring Things, Including Lengths 1 1.2 Time 5 1.3 Mass 6 2 Motion Along a Straight Line 13 2.1 Position, Displacement, and Average Velocity 13 2.2 Instantaneous Velocity and Speed 18 2.3 Acceleration 20 2.4 Constant Acceleration 23 2.5 Free-Fall Acceleration 28 2.6 Graphica...

CWB Welding Inspector Level 1 Exam (Latest 2024 / 2025 Update) Questions and Verified Answers | 100% Correct | Grade A Q: From the welding problems identified below which one of the five does not fit the pattern established by the other four? a) Insufficient throat. b) Incorrect bevel angle. c) Loss of shielding gas. d) Improper fit up. e) Use of wrong consumable. Answer: a) Insufficient throat. Q: A 10 mm fillet weld has a nominal: a) Throat dimension of 10 mm. b) Area of 10 sq. mm. c) Leg size...

CWB Welding Inspector Level 1 Exam (Latest 2023/ 2024 Update) Questions and Verified Answers| 100% Correct| Grade A Q: From the welding problems identified below which one of the five does not fit the pattern established by the other four? a) Insufficient throat. b) Incorrect bevel angle. c) Loss of shielding gas. d) Improper fit up. e) Use of wrong consumable. Answer: a) Insufficient throat. Q: A 10 mm fillet weld has a nominal: a) Throat dimension of 10 mm. b) Area of ...

Fracture is a type of material failure. Of the following which is another type of material failure? - Permanent deformation. Which of the following statements best differentiates between a defect and a discontinuity? - Discontinuities can propagate and become defects. Nondestructive testing is often differentiated from other measurements or inspection techniques in that: - NDT involves indirect tests related to some other quality or characteristic of material. What are the functions of ...

ASE A6 Test Prep – Electrical/Electronic Systems - Questions, Answers and Explanations Adding an additional path through which the current can flow has decreased the total resistance of the circuit. Each light drops 12 volts. An ohmmeter is being used to check a circuit for continuity. Technician A says an infinity or full scale reading on an ohmmeter indicates no continuity. Technician B says a zero reading on an ohmmeter indicates continuity. Who is right? A. Technician A only B. Technician...