MSSC Safety Study guides, Class notes & Summaries

MSSC Maintenance awareness practice test (2024/2025) Rated A+ A burn or pungent odor of oil indicates - Answer ️️ -excessive temperature A Chain should be replaced when its length becomes ______longer than the original length. - Answer ️️ -3 percent A common sign of a misaligned coupling is _____________. - Answer ️️ -excessive vibration A multimeter is a multipurpose devise that can measure - Answer ️️ -voltage, current, and resistance A power diagram is used in addition...

When connecting a 3-phase motor the three lines (T1,T2 and T3) are usually connected to __________. - L1, L2, and L3 Electricians use __________ to prevent damage to electrical wiring running to the machine. - rigid and flexible conduit When the wire or foil strip inside a fuse melts, the fuse is said to be __________. - blown The difference between a fuse and a circuit breaker is __________. - circuit breakers can be reset and used again The amount two electrical waveforms are out of pha...

Ohms Measurement of electrical resistance Amperes Measurement of current in an electrical circuit Volts Measurement of potential or force in an electrical circuit Watts Measurement of power in an electrical circuit Strainer Filter found on suction line in a hydraulic tank AND Logic Two or more normally open switches in series NOT Logic Normally closed switch used for emergency stop NOR Logic Two or more normally closed switches in series NAND Logic Two or more normally closed switches in...

true, because the auditor is responsible for an accurate report of all findings CPT Quality and Measurement Consider the statement "Even if corrective action is taken immediately for a finding during the audit, all significant deficiencies should be detailed in the written report" This statement is Ensure that procedures and processes are followed The purpose of a quality audit program is Measurement and calibration While on the production floor which of the following is audited obtain r...

A scale typically found on a tape measure is ______ 1/16 Two systems of dimensional measurement used in manufacturing are the SI Metric System and the _____ US Customary System A common decimal-inch graduation is _____ 10ths, 50ths, 100ths Resolution is sometimes called ____ discrimination A common scale on a machinist's rule is _____ 150 mm Dimensional measurement determines physical dimensions such as width, height, depth, and diameter If the length of a part is 5.000 inches and the r...

What are the steps of a job safety analysis? Document an itemized sequence of job task,Identify the hazard of each task, Propose potential solutions to problems and Prepare a list of potential problems What does NIOSH stand for? Nation Institute for Occupational Safety and Health OSHA The federal agency concerned with the enforcement and regulation of safety regulations. The risk of injury for new employees is more or less likely than for those with experience? More likely. They are 40% mor...

Continuous flow layouts are used only when low volumes of different parts must be produced. Is this statement TRUE or FALSE? False Engineers and plant managers can easily check on operations in their own plant, or halfway around the world, due to advancements in __________. communications The quality assurance department monitors the production process to ensure that products meet __________. customer specifications The origins of manufacturing can be traced back to the beginning of agricu...

The three common types of mechanisms are levers, ______, and inclined planes. wheels The metric system expresses force in ______. newtons A spring scale is used to measure ______. force The English unit of measure of weight is the ______. pound-force (lb-f) The Law of Moments can be used to determine ______. both the force needed to balance OR force needed to move a load Torque can be calculated by multiplying the distance from the fulcrum and ______. the force applied A force that makes ...

Continuous flow layouts are used only when low volumes of different parts must be produced. Is this statement TRUE or FALSE? False Engineers and plant managers can easily check on operations in their own plant, or halfway around the world, due to advancements in __________. communications The quality assurance department monitors the production process to ensure that products meet __________. customer specifications The origins of manufacturing can be traced back to the beginning of agricu...

MSSC Maintenance Test Questions and Answers Follow-up work created after PM is considered... - CORRECT ANSWER-Corrective When lubricating a bearing, the worst mistake would be to... - CORRECT ANSWER-Get dirt in the bearing What would be classified as an unplanned downtime maintenance? - CORRECT ANSWER-Reactive maintenance Circuit testers determine if ___ electricity is present. - CORRECT ANSWER-AC When checking for out of round, any movement of the dial indicates that the... - CORREC...

MSSC CLT Terms Study Guide Exam Airway bill - CORRECT ANSWER-A bill of lading for air transport that serves as a receipt for the shipper, indicates that the carrier has accepted the goods listed, obligates the carrier to carry the consignment to the airport of destination according to specified conditions. Advanced ship notice (ASN) - CORRECT ANSWER-An electronic data interchange (EDI) notification of shipment of product. Aggregate inventory management - CORRECT ANSWER-Establishing th...